Practice test for ccna 200-301 set 24

In this article I provide you online dummy practice test for ccna 200-301. The questions of this article practice test for ccna 200-301 may be helpful you to check your knowledge about networking or ccna exam 200-301. This test for ccna 200-301 contains a 10 questions mcq related to Network Access. There are many online websites and books available for Practice for ccna 200-301 exam. You can found these resources easily via any online search engine like google or yahoo etc. Along with these resources attempt the test for ccna 200-301 on this website may be helpful you to build confidence and check your knowledge.

How to attempt this Practice test for ccna 200-301 set 24

This article have 10 questions with multiple answers. You need to select the correct answer and at the end of the quiz just click on the button “click to check your answer”. A message will prompt on your screen with the exam score. You can also see the correct answers on page. So play the below quiz and do a dummy test for ccna 200-301 to check your knowledge about ccna 200-301 exam. At the end of this article link available for next or previous quiz. The complete list of all quiz is available for dummy test for ccna 200-301 here.


  • 1. Two switches are connected via ethernet port. Both switches have same VLANs which of the following is correct statement in this scenerio.


    A) Both interfaces should be assigned same IP network series to make communication.

    B) Both interfaces should be configured as trunk port to make communication.

    C) Both interface should be up and not shut down.

    D) VTP should be configured on both interfaces.

  • 2. Whai is required to do when Cisco and Dell switch connected with each other?


    A) The Cisco switch must be configured as 802.1Q.

    B) Dell switch must be configured to use ISL.

    C) Both switches must be configured same VLAN.

    D) VTP needs to be configured in both switches.

  • 3. Which of the following command can be used to see all trunks on a switch?


    A) Sw#show trunk.

    B) Sw#show switchport.

    C) Sw#show switchport trunk all.

    D) Sw#show switchport trunk.

  • 4. What is the default VTP mode in all switches ?


    A) Trunk.

    B) Access.

    C) Client.

    D) Server.

  • 5. Which of the following command can be used to verify the VTP mode on a switch ?


    A) Sw#show vtp .

    B) Sw#show vtp counters .

    C) Sw#show vtp status .

    D) Sw#show running-config .

  • 6. Which of the following commands can be used to configre VTP in a switch ?


    A) Sw(config)#vtp client

    Sw(config)#vtp domain corpname.

    B) Sw(config)#vtp mode client

    Sw(config)#vtp domain corpname.


    C) Sw(config)#vtp mode client

    Sw(config)#vtp domain .

    D) Sw(config)#vtp client

    Sw(config)#vtp domain corpname.

  • 7. Which of the following command can be used to remove VLAN 10 through 20 without disturbing the whole network ?


    A) Sw(config-if)#switchport remove vlan 10-20.

    B) Sw(config-if)#switchport trunk remove vlan 10-20 .

    C) Sw(config-if)#switchport trunk vlan 10-20 remove.

    D) Sw(config-if)#switchport trunk allowed vlan remove 10-20 .

  • 8. Which of the following command can be used to set the existing trunk back to default ?


    A) Sw(config-if)#switchport trunk allowed vlan all .

    B) Sw(config-if)#switchport trunk vlan all .

    C) Sw(config-if)#switchport trunk vlan all .

    D) Switch(config-if)#switchport trunk allowed all .

  • 9. Which command can be used to add VLAN 10 to a trunk interface without intruption to the network ?


    A) Sw(config-if)#switchport trunk allowed add vlan 10 .

    B) Sw(config-if)#switchport trunk allowed vlan add 10 .

    C) Sw(config-if)#switchport allowed vlan add 4 .

    D) Sw(config-if)#switchport trunk allowed vlan 4 add .

  • 10. How to fix the error message "command rejected: An interface whose trunk encapsulation is Auto can not be configured to trunk mode" when trying to change the mode trunk of a switchport ?


    A) Sw(config-if)#switchport trunk encapsulation dot1q .

    B) Sw(config-if)#no switchport trunk encapsulation dot1q .

    C) Sw(config-if)#switchport encapsulation dot1q .

    D) Sw(config-if)#switchport trunk dot1q .



Attend all Practice exam for ccna 200-301 on this site. Every quiz on this website have different questions there are approx 200 quiz available here on this site for Practice exam for ccna 200-301. for explanation of any question you may explore our website via this link. This website covers almost topics of CCNA 200-301.

You may also like to read --  Practice test for ccna 200-301 set 88

I hope you found this Practice exam for ccna 200-301 interesting and useful. You can take more Practice test for ccna 200-301 on this website. For any query or suggestions you may drop a comment below or contact us. Read more articles for CCNA on this site. Share this webpage in your social circle by the icons below.

Share this article in your social circle :)
,

Leave a Reply

Your email address will not be published. Required fields are marked *