Practice test for ccna 200-301 set 23

In this article I provide you online dummy practice test for ccna 200-301. The questions of this article practice test for ccna 200-301 may be helpful you to check your knowledge about networking or ccna exam 200-301. This test for ccna 200-301 contains a 10 questions mcq related to Network Access. There are many online websites and books available for Practice for ccna 200-301 exam. You can found these resources easily via any online search engine like google or yahoo etc. Along with these resources attempt the test for ccna 200-301 on this website may be helpful you to build confidence and check your knowledge.

How to attempt this Practice test for ccna 200-301 set 23

This article have 10 questions with multiple answers. You need to select the correct answer and at the end of the quiz just click on the button “click to check your answer”. A message will prompt on your screen with the exam score. You can also see the correct answers on page. So play the below quiz and do a dummy test for ccna 200-301 to check your knowledge about ccna 200-301 exam. At the end of this article link available for next or previous quiz. The complete list of all quiz is available for dummy test for ccna 200-301 here.


  • 1. What needs to be done when Cisco VoIP phone not working refer the exhibit "no cdp enable", "spanning-tree portfast", "switchport mode access" ?


    A) STP needs to be removed

    B) CDP need to be enable.

    C) Switchport mode need to change to trunk.

    D) Switchport mode needs to be changed to VoIP mode.

  • 2. Which of the following command can be used to check the interface relates to VLAN, status of interface and operation mode ?


    A) Sw#show vlan.

    B) Sw#show running-config.

    C) Sw#show interfaces.

    D) Sw#show interface switchport.

  • 3. Which of the following command can be used to enable a VLAN ?


    A) Sw(config)#enable vlan 10.

    B) Sw(config)#no shutdown vlan 10.

    C) Sw(config)#vlan 10 and Sw(config-vlan)#no shutdown.

    D) Sw#vlan 10.

  • 4. Which of the following command will show the operation mode of a perticular interface ?


    A) Sw#show interfaces FastEthernet 0/1 switchport .

    B) Sw#show interfaces FastEthernet 0/1 .

    C) Sw#show interfaces switchport.

    D) Sw#show interfaces switchport FastEthernet 0/1.

  • 5. The guest VLAN is not allow traffic to be routed. What may be the best related cause for this from the following ? the exhibit show "act/lshut Fa0/10"


    A) The VLAN is shutdown.

    B) The VLAN is disabled.

    C) The interface is not belongs to the required VLAN.

    D) the interface may be shutdown.

  • 6. Which of the following sequence of commands can be used to create new VLAN 10 and apply it to interface Fa0/1. ?


    A) Sw(config)#vlan 10

    Sw(config-vlan)#name test

    Sw(config-vlan)#exit

    Sw(config)#interface fastethernet 0/1

    Sw(config -if)#switchport acess vlan test.

    B) Sw(config)#vlan 10 test

    Sw(config-vlan)#exit

    Sw(config)#interface fastethernet 0/1

    Sw(config -if)#switchport acess vlan test.

    C) Sw(config)#vlan 10

    Sw(config-vlan)#name test

    Sw(config)#interface fastethernet 0/1

    Sw(config -if)#switchport acess vlan 10.

    D) Sw(config)#vlan 10

    Sw(config-vlan)#name test

    Sw(config-vlan)#exit

    Sw(config)#interface fastethernet 0/1

    Sw(config -if)#switchport acess vlan 10.


  • 7. What do you understand when "VLAN0004 active" shown in exhibit?


    The VLAN is not named.

    B) The VLAN is suspended.

    C) The VLAN is in by default VLAN.

    D) The VLAN is not working.

  • 8. A VLAN is not showing in VLAN database, What must be done to resolve the issue?


    A) VLAN may be shut down.

    B) VLAN may be not active.

    C) Create the VLAN manually.

    D) Configure the VTP.

  • 9. What is required to make communication between two different VLANs?


    A) The VLAN must be enabled.

    B) Routing requires between different VLANs.

    C) VTP required to be configured.

    D) Another switch required to connect both VLANs.

  • 10. Which of the following command can be used to see the interface status, IP address on interface in a router ?


    A) Router#show interface.

    B) Router#show interface brief.

    C) Router#show ip interface.

    D) Router#show ip interface brief.



Attend all Practice exam for ccna 200-301 on this site. Every quiz on this website have different questions there are approx 200 quiz available here on this site for Practice exam for ccna 200-301. for explanation of any question you may explore our website via this link. This website covers almost topics of CCNA 200-301.

I hope you found this Practice exam for ccna 200-301 interesting and useful. You can take more Practice test for ccna 200-301 on this website. For any query or suggestions you may drop a comment below or contact us. Read more articles for CCNA on this site. Share this webpage in your social circle by the icons below.

Share this article in your social circle :)
You may also like to read --  Practice test for ccna 200-301 set 72
,

Leave a Reply

Your email address will not be published. Required fields are marked *